Aros Syncro 1000 Manual de Instruções

RInstallation and Hardware GuideARO-1130CARAIDport II Cardfor Personal Workstations

1-11▼ ▼ ▼ ▼IntroductionThe Adaptec® ARO™-1130CA RAIDport II™ Card provides power-ful disk array support in personal workstations with RAIDport II o

1-2ARO-1130CA Installation and Hardware Guide 64 MBytes or more of system memory recommended for Windows NT WorkstationUsing the ARO-1130CA with Other

1-3IntroductionInstallation OverviewThe steps involved in installing the ARO-1130CA hardware and software are1Locate the PCI RAIDport II slot on the m

2-12▼ ▼ ▼ ▼Installing the ARO-1130CA and Connecting SCSI DevicesThis chapter explains how to install your hardware. To install the ARO-1130CA and d

2-2ARO-1130CA Installation and Hardware GuideARO-1130CA LayoutFigure 2-1 identifies the major ARO-1130CA components. You may find it helpful to refer

2-3Installing the ARO-1130CA and Connecting SCSI DevicesVerifying Presence of DIMM MemoryBefore you can use the ARO-1130CA, the DIMM memory socket mus

2-4ARO-1130CA Installation and Hardware GuideInstalling the ARO-1130CAFollow these steps to install the ARO-1130CA:Note: If you are installing the ARO

2-5Installing the ARO-1130CA and Connecting SCSI DevicesConnecting the LED Activity Indicator to the ARO-1130CA(Optional feature) An LED on the front

Adaptec, Inc.691 South Milpitas BoulevardMilpitas, CA 95035© 1997 Adaptec, Inc.All rights reserved. Adaptec, and the Adaptec logo are trade-marks of

2-6ARO-1130CA Installation and Hardware GuideConnecting SCSI DevicesThe ARO-1130CA supports both internal and external SCSI devices. Depending on the

2-7Installing the ARO-1130CA and Connecting SCSI DevicesConnecting Internal SCSI DevicesFollow these steps to connect internal devices:1Prepare each S

2-8ARO-1130CA Installation and Hardware Guide4Attach the remaining connectors on the cable to the remaining internal devices.5Connect an available DC

2-9Installing the ARO-1130CA and Connecting SCSI DevicesOnce the SCSI port expansion kit is installed, follow these steps to connect external SCSI dev

2-10ARO-1130CA Installation and Hardware Guide3Attach the connector at the other end of the cable to either one of the SCSI connectors on the external

2-11Installing the ARO-1130CA and Connecting SCSI Devices4Connect other external SCSI devices by daisy-chaining each device to the previous device unt

2-12ARO-1130CA Installation and Hardware GuideConnecting SCSI Array Enclosures (Storage Subsystems)To help you conveniently manage your SCSI storage s

2-13Installing the ARO-1130CA and Connecting SCSI DevicesInstallation Hints for Connecting SCSI DevicesAll SCSI Devices If you are booting your system

2-14ARO-1130CA Installation and Hardware Guide When calculating the total length of the bus, be sure to include the cabling inside any array enclosure

2-15Installing the ARO-1130CA and Connecting SCSI DevicesCompleting the InstallationReinstall your computer cover and connect all power cables. To ver

R▼ ▼ ▼ ▼ ARO-1130CARAIDport II Cardfor Personal WorkstationsInstallation and Hardware Guide

3-13▼ ▼ ▼ ▼Creating the First Array With the ArrayConfigCA ProgramThis chapter explains how to use the Adaptec ArrayConfigCA pro-gram to create the

3-2ARO-1130CA Installation and Hardware GuideCreating an Array with Express SetupArrayConfigCA’s Express Setup option allows you to quickly create an

3-3Creating the First Array With the ArrayConfigCA Program– Select Optimized for Data Protection if your main concern is to protect the files on the a

3-4ARO-1130CA Installation and Hardware GuideCreating an Array with Custom SetupArrayConfigCA’s Custom Setup option allows advanced users to create ar

3-5Creating the First Array With the ArrayConfigCA Program8Type the number of drives you want in the array (this does not include spares) and press En

3-6ARO-1130CA Installation and Hardware GuidebAt the next prompt, type 1 or 2.cSelect one or two spares, using the same method you used to select disk

3-7Creating the First Array With the ArrayConfigCA ProgramMaking the Array BootableYou can make the array bootable so that the computer boots from the

3-8ARO-1130CA Installation and Hardware GuideNote: You cannot designate a stand-alone SCSI disk drive the boot order of Unit 0. If you want to do this

4-14▼ ▼ ▼ ▼Installing Software on a Windows NT SystemThis chapter explains how to install the software required to use the ARO-1130CA in a system u

iiCopyright© 1997 Adaptec, Inc. All rights reserved. No part of this publication may be repro-duced, stored in a retrieval system, or transmitted in a

4-2ARO-1130CA Installation and Hardware GuideInstalling the Array1000CA Driver for Windows NTThis section explains how to install the Array1000CA Mini

4-3Installing Software on a Windows NT System3Press S to skip autodetection of your SCSI host adapter.4Press S again to specify an additional device.5

4-4ARO-1130CA Installation and Hardware Guide8In the Install Driver window, Click OK.9Click the New button when asked if you want to use the cur-rentl

4-5Installing Software on a Windows NT System6Double-click the CI/O Array Management Software icon to start the program.See the Adaptec ARO-1130CA Arr

5-15▼ ▼ ▼ ▼Configuring the ARO-1130CA with the SCSISelect UtilityThe Array1000CA SCSISelect® configuration utility allows you to change controller

5-2ARO-1130CA Installation and Hardware GuideDefault SCSISelect SettingsThe default SCSISelect settings, shown in the table below, are appro-priate fo

5-3Configuring the ARO-1130CA with the SCSISelect UtilityStarting the SCSISelect UtilityTo start SCSISelect, press Ctrl-A when the following prompt ap

5-4ARO-1130CA Installation and Hardware GuideExiting SCSISelectTo exit SCSISelect, press Esc until a message prompts you to exit (if you changed any h

5-5Configuring the ARO-1130CA with the SCSISelect UtilitySCSISelect SettingsSCSI Bus Interface DefinitionsThe following settings are the SCSISelect se

iiiFederal Communications Commission Radio Frequency Interference StatementWARNING: Changes or modifications to this unit not expressly approved by th

5-6ARO-1130CA Installation and Hardware GuideSCSI Device ConfigurationThe SCSI device settings allow you to configure certain parameters for each devi

5-7Configuring the ARO-1130CA with the SCSISelect Utility Send Start Unit Command—This option determines whether the Start Unit Command is sent to the

A-1A▼ ▼ ▼ ▼TroubleshootingTroubleshooting ChecklistCheck the following if you have problems installing or running the ARO-1130CA and SCSI devices:

A-2ARO-1130CA Installation and Hardware GuideProblems Running the Software On Your Windows NT WorkstationIf the Adaptec CI/O Workstation Array Managem

A-3Troubleshooting Verify that the following DLLs are located in your system32 directory. If they are not present, try reinstalling the Adaptec CI/O W

A-4ARO-1130CA Installation and Hardware GuideUsing the ARO-1130CA with an AHA-2940 Family Host AdapterThis section explains how to use an ARO-1130CA a

A-5TroubleshootingChanging Registry Settings1Back up the NT Registry, using one of the techniques described in Backing up the Windows NT Registry on p

A-6ARO-1130CA Installation and Hardware GuideThis table of hexidecimal numbers indicates the Tag-value sequence in which the SCSI Miniport drivers are

A-7Troubleshooting12Select cda1000 on the left part of the screen. Click the right mouse button on Tag Value on the right part of the screen and selec

A-8ARO-1130CA Installation and Hardware Guide4When the Install from Disk dialog box appears, type A:\winnt on the command line and click OK.5Select Ad

A-9TroubleshootingA table appears with columns of two- and four-number groups, something like this:0005 02 00 00 00 03 00 00 000010 01 00 00 00 01 01

A-10ARO-1130CA Installation and Hardware Guide10Compare the Tag value loading sequence to the actual tag val-ues of cda1000 and aic78xx that you deter

A-11Troubleshooting Run the rdisk utility with the /s option to create a copy of the Registry on a hard disk. (A typical backup file is 5 MBytes to 10

B-1B▼ ▼ ▼ ▼Advanced TopicsInstalling Multiple AdaptersYou cannot install more than one ARO-1130CA card in the same sys-tem unless the system is des

C-1C▼ ▼ ▼ ▼Using a CD-ROM Drive with DOSTo operate a SCSI CD-ROM drive connected to the ARO-1130CA under DOS, you need The SCSI driver, aspi8dos.sy

C-2ARO-1130CA Installation and Hardware Guide Sample command lines for config.sys file:device=c:\scsi\aspi8dos.sys /ddevice=c:\scsi\aspicd.sys /d:aspi

C-3Using a CD-ROM Drive with DOS/norst /norst Prevents aspi8dos from resetting the SCSI bus when you boot your computer. By default, aspi8dos resets t

v▼ ▼ ▼ ▼ Contents1 IntroductionSystem Requirements 1-1Using the ARO-1130CA with Other Adaptec Products 1-2Installation Overview 1-32 Installing

C-4ARO-1130CA Installation and Hardware Guide❒Command Line Options for aspicd.sysOption Example Use/d:<name>/d:aspicd0 Required in the config.sy

D-1D▼ ▼ ▼ ▼Obtaining SCSI Cables and ConvertersHigh-quality cables are required in high-performance SCSI systems to ensure data integrity. Adaptec

D-2ARO-1130CA Installation and Hardware GuideExternal CablesInternal Ribbon CablesConverters❒1 ACK-F2F-5IT and ACK-W2W-5IT have built-in active termin

E-1E▼ ▼ ▼ ▼Listing of VendorsThis appendix contains a partial listing of array storage enclosure and SCSI disk drive manufacturers.Array Storage En

E-2ARO-1130CA Installation and Hardware GuideSCSI Disk Drive ManufacturersFujitsu Computer Products of America, Inc.2904 Orchard ParkwaySan Jose, CA 9

Index-1▼ ▼ ▼ ▼ IndexAAdaptec CI/O Workstation Array Management Software 4-4Advanced topics B-1AHA-2940 Family Driver, installing A-7AHA-2940 Fam

ARO-1130CA Installation and Hardware GuideIndex-2EEnable disconnection 5-2, 5-6Enclosure, Array 2-6, D-1Expansion slot 2-4, A-1External devices 2-8FFo

Index-3IndexSCSISelect Utility 5-1–5-7default settings 5-2Send start unit command 5-2, 5-7Services 4-4Synchronous negotiation 5-2, 5-6Synchronous tran

viARO-1130CA Installation and Hardware Guide4 Installing Software on a Windows NT SystemInstalling the Array1000CA Driver for Windows NT 4-2Installing

viiContentsC Using a CD-ROM Drive with DOSD Obtaining SCSI Cables and ConvertersExternal Cables D-2Internal Ribbon Cables D-2Converters D-2E Listing o